What have you done to your RX-8 today????
-
- Spin Doctor
- Posts: 32586
- Joined: Sat Sep 06, 2008 10:56 pm
- RX-8: 231
- Colour: Lightning Yellow
- Location: Groomsport, Co Down, NI
- Has thanked: 442 times
- Been thanked: 2088 times
Re: What have you done to your RX-8 today????
I saw a program a couple of weeks ago where they were saying that a huge percentage (over 70% in London) of hybrid vehicles are being driven as just petrol-powered, all the time. Many are being returned at end-of-lease with the charging cable still sealed in the original packaging.
Companies/drivers are being given tax incentives and charge exclusions for choosing these car but the technology is just dead-weight.
Drivers can't be bothered and the infrastructure just isn't in place.
Last time I went to Hospital, I found half of the 2nd floor of the multi-storey carpark is now designated for electric vehicles, and every one of those spaces were taken. Though I didn't bother to check if all the cars were electric but I did notice that only two were actually plugged-in.
Companies/drivers are being given tax incentives and charge exclusions for choosing these car but the technology is just dead-weight.
Drivers can't be bothered and the infrastructure just isn't in place.
Last time I went to Hospital, I found half of the 2nd floor of the multi-storey carpark is now designated for electric vehicles, and every one of those spaces were taken. Though I didn't bother to check if all the cars were electric but I did notice that only two were actually plugged-in.
-
- Club Member
- Posts: 3397
- Joined: Sat Dec 03, 2016 8:38 pm
- RX-8: R3
- Colour: Sparkling Black
- Location: Colchester, Essex
- Has thanked: 695 times
- Been thanked: 561 times
Re: What have you done to your RX-8 today????
Yeah it's been yet another massive scam, with no one apparently to be held accountable.
I'm having a Renault Zoe, so a full on EV. On a rental hire rather than proper lease, so there's no cash bung for me from the government. But it is only £200ish pounds a month to hire (all in) and that's less than I pay in fuel alone, so it pays for itself. It's only a monthly rolling contract too, so you can skip a month and restart later in the year. So there's no long contract period.
But yeah, whether the charge points will be blocked by non-charging vehicles is another matter. I'm used to similar when people who shouldn't swipe the parent and child bay right in front of me. Infuriating it is, and not fair that my little ones have to cross a dangerous car park so that 'Madame' in her Chelsea Tractor has a shorter walk to the shop.
I'm having a Renault Zoe, so a full on EV. On a rental hire rather than proper lease, so there's no cash bung for me from the government. But it is only £200ish pounds a month to hire (all in) and that's less than I pay in fuel alone, so it pays for itself. It's only a monthly rolling contract too, so you can skip a month and restart later in the year. So there's no long contract period.
But yeah, whether the charge points will be blocked by non-charging vehicles is another matter. I'm used to similar when people who shouldn't swipe the parent and child bay right in front of me. Infuriating it is, and not fair that my little ones have to cross a dangerous car park so that 'Madame' in her Chelsea Tractor has a shorter walk to the shop.
-
- Former Member
- Posts: 223
- Joined: Tue Mar 06, 2018 7:30 pm
- RX-8: 40th Anniversary
- Colour: Custom
- Location: Bromsgrove
- Has thanked: 82 times
- Been thanked: 60 times
Re: What have you done to your RX-8 today????
Noticed an oil leak on the driver's side, FR wheel covered in the stuff and pooled underneath. From what I've looked up it seems to be the oil cooler line. Sent it in to the lads at the garage...
Sent from my SM-G960F using Tapatalk
Sent from my SM-G960F using Tapatalk
R3-40th Anniversary [97/400] R3 face conversion in Ford Frozen White (originally Met Grey)
Engine Rebuild at 96,###.
Full bridge port
Tuned by Rotary Revs @209whp
Lightweight flywheel
Mazda Rev C Coils
AEM CAI
Racing Beat catback
Dual Res Decat
R-Magic Exhaust Manifold
Rota Pro R 18"/9.5
Yokohama AD08RS 255/40/18
TEIN Flex Z Coilovers
Whiteline ARBs
Engine Rebuild at 96,###.
Full bridge port
Tuned by Rotary Revs @209whp
Lightweight flywheel
Mazda Rev C Coils
AEM CAI
Racing Beat catback
Dual Res Decat
R-Magic Exhaust Manifold
Rota Pro R 18"/9.5
Yokohama AD08RS 255/40/18
TEIN Flex Z Coilovers
Whiteline ARBs
-
- Former Member
- Posts: 4726
- Joined: Sun Jan 10, 2016 10:14 pm
- RX-8: 231
- Colour: Velocity Red
- Location: Leicestershire
- Has thanked: 265 times
- Been thanked: 359 times
Re: What have you done to your RX-8 today????
Unusual for that one to go but not unheard of.
You'll struggle to find the line for sale on its own, so maybe best bet is to have one made up at your local hydraulic supplier.
The one that goes from cooler to cooler I've had made for about £50 in the past.
About £150 for a full kit.
You'll struggle to find the line for sale on its own, so maybe best bet is to have one made up at your local hydraulic supplier.
The one that goes from cooler to cooler I've had made for about £50 in the past.
About £150 for a full kit.
-= Rotormelon Money Pit Build of Tasteless Questionable Bodgery =-
Experimelon 183whp rebuild | Rotary Revs D585s | PZ Suspension | Hawk & Yellowstuff pads | Extra steering lock | Custom exhaust | Added rearward flames of glory | Unnecessarily repurposed ball gags-= Clicky click for build thread =-
-
- Former Member
- Posts: 223
- Joined: Tue Mar 06, 2018 7:30 pm
- RX-8: 40th Anniversary
- Colour: Custom
- Location: Bromsgrove
- Has thanked: 82 times
- Been thanked: 60 times
Re: What have you done to your RX-8 today????
That was the diagnosis they gave, and that's what they're getting done.
Apparently it made a total mess of the brakes (which I just got replaced )as well, so they're doing something or other to those.
So sadly I won't be able to get her back until tomorrow.
R3-40th Anniversary [97/400] R3 face conversion in Ford Frozen White (originally Met Grey)
Engine Rebuild at 96,###.
Full bridge port
Tuned by Rotary Revs @209whp
Lightweight flywheel
Mazda Rev C Coils
AEM CAI
Racing Beat catback
Dual Res Decat
R-Magic Exhaust Manifold
Rota Pro R 18"/9.5
Yokohama AD08RS 255/40/18
TEIN Flex Z Coilovers
Whiteline ARBs
Engine Rebuild at 96,###.
Full bridge port
Tuned by Rotary Revs @209whp
Lightweight flywheel
Mazda Rev C Coils
AEM CAI
Racing Beat catback
Dual Res Decat
R-Magic Exhaust Manifold
Rota Pro R 18"/9.5
Yokohama AD08RS 255/40/18
TEIN Flex Z Coilovers
Whiteline ARBs
-
- Forum Moderator
- Posts: 2496
- Joined: Wed May 17, 2017 12:27 pm
- RX-8: 231
- Colour: Sunlight Silver
- Location: Tyne & Wear
- Has thanked: 150 times
- Been thanked: 162 times
Re: What have you done to your RX-8 today????
I have known people try the wankel solution on the friction material for oil contamination.... Burn it off (using acetylene)
But for the cost of pads I dont think I'd risk it, and everything else will clean up.
But for the cost of pads I dont think I'd risk it, and everything else will clean up.
Sunlight Silver 231
Pete/Peter him/he/hrh couldn't really care as have 3 siblings and was lucky not to get called by the dogs name.
Living with a rotary - 7 Years in
viewtopic.php?p=1105043#p1105043
Pete/Peter him/he/hrh couldn't really care as have 3 siblings and was lucky not to get called by the dogs name.
Living with a rotary - 7 Years in
viewtopic.php?p=1105043#p1105043
-
- Former Member
- Posts: 487
- Joined: Wed Oct 03, 2007 7:35 pm
- RX-8: R3
- Colour: Diamond Grey
- Location: Leeds
- Has thanked: 4 times
- Been thanked: 6 times
Re: What have you done to your RX-8 today????
No chance!ChrisHolmes wrote: ↑Tue Dec 18, 2018 7:48 pmHave the crackle map taken off and that shoukd improve your mpg.
Diamond Grey R3. RR D585 Ignition Coils & Magnecor Leads. Pettit Racing / Milltek Catback. RB Dual-Res Decat. RR Custom Remap + Pops & Bangs
-
- Former Member
- Posts: 1391
- Joined: Sun Jun 11, 2017 1:25 pm
- RX-8: 231
- Colour: Galaxy Grey
- Location: Newport
- Has thanked: 33 times
- Been thanked: 38 times
Re: What have you done to your RX-8 today????
- These users thanked the author wiggles for the post:
- Nickp47 (Sun Dec 23, 2018 10:20 am)
Project thread Galaxy grey 231 - Street Port, Tein coilovers, decat, D585's, Cobra Catback whatever 9j wheels aren't broken at the moment and a massive wing
-
- Former Member
- Posts: 1454
- Joined: Mon Nov 26, 2018 8:27 pm
- RX-8: 231
- Colour: Velocity Red
- Location: Shropshire
- Has thanked: 16 times
- Been thanked: 87 times
Re: What have you done to your RX-8 today????
I spent a rather drizzly day preparing the stock alloys for a respray. Sanding back all the old paint which had started to peel and react in places. Going for a nice easy gloss black to compliment the velocity red.
Sent from my Pixel 2 XL using Tapatalk
Sent from my Pixel 2 XL using Tapatalk
Last edited by shroom on Sun Dec 23, 2018 11:58 pm, edited 1 time in total.
-
- Club Member
- Posts: 17190
- Joined: Sun Feb 18, 2018 1:12 pm
- RX-8: Kuro
- Colour: Kuro Black
- Location: oswestry shropshire
- Has thanked: 219 times
- Been thanked: 350 times
Re: What have you done to your RX-8 today????
hi mate, what sort of condition are the tyres in? if they are near the end i would take them off and have the wheels blasted and baked,the results will be so much better than with leaving tyres on .
Rob
-
- Former Member
- Posts: 1454
- Joined: Mon Nov 26, 2018 8:27 pm
- RX-8: 231
- Colour: Velocity Red
- Location: Shropshire
- Has thanked: 16 times
- Been thanked: 87 times
Re: What have you done to your RX-8 today????
They ain't the best fair bit of kerb rash and bubbles etc. Not wanting to spend a lot on sending them somewhere so doing it over Christmas.
Sent from my Pixel 2 XL using Tapatalkgoodeggbob wrote:hi mate, what sort of condition are the tyres in? if they are near the end i would take them off and have the wheels blasted and baked,the results will be so much better than with leaving tyres on .
-
- Club Member
- Posts: 67
- Joined: Wed Oct 15, 2014 10:05 pm
- RX-8: Evolve
- Colour: Copper Red
- Location: Stourbridge, West Midlands
- Has thanked: 2 times
- Been thanked: 7 times
Re: What have you done to your RX-8 today????
Bought a lovely set of valve caps for my Evolve’s Christmas present to match the lightweight wheelnuts
You do not have the required permissions to view the files attached to this post.
No Pistons:
2004 231 PS Titanium Grey RX-8
2006 Copper Red Evolve RX-8
1993 Montego Blue RX-7 FD3S
Previous: 2005 231 PS Velocity Red RX-8
2004 231 PS Titanium Grey RX-8
2006 Copper Red Evolve RX-8
1993 Montego Blue RX-7 FD3S
Previous: 2005 231 PS Velocity Red RX-8
-
- Former Member
- Posts: 901
- Joined: Sat Dec 19, 2015 6:08 pm
- Location: London
- Has thanked: 66 times
- Been thanked: 45 times
Re: What have you done to your RX-8 today????
Any nut pics?
I’ve always been tempted by lightweight nuts but it’s hard to be sure how safe they will be.
RX8 R3 Aurora Blue Mica
BHR coils+MSD leads, Stage 1 ecu tune, HKS Hybrid oil filter, Idemitsu 10w30, BHR engine mounts, RB oil cooler lines, Essex Rotary undertray, RB Revi Intake+Ram Air, Milltek/Pettit cat+catback, braided brake lines, SuperPro bushes, RB flywheel, Exedy stage 1 clutch, Pettit Ti flywheel nut, powder coated and fully resealed everything underneath
BHR coils+MSD leads, Stage 1 ecu tune, HKS Hybrid oil filter, Idemitsu 10w30, BHR engine mounts, RB oil cooler lines, Essex Rotary undertray, RB Revi Intake+Ram Air, Milltek/Pettit cat+catback, braided brake lines, SuperPro bushes, RB flywheel, Exedy stage 1 clutch, Pettit Ti flywheel nut, powder coated and fully resealed everything underneath
-
- Club Member
- Posts: 8037
- Joined: Sun Sep 28, 2014 9:11 pm
- RX-8: 40th Anniversary
- Colour: Crystal White
- Location: poole dorset
- Has thanked: 742 times
- Been thanked: 284 times
Re: What have you done to your RX-8 today????
I think this has been talked about before ! Unless there decent ones I wouldn't be driving to fast with them or on track !
Sent from my SM-G930F using Tapatalk
Sent from my SM-G930F using Tapatalk
Hayward's Street/bridgeported rebuild,595's,Tein coilovers edfc Racingbeat rear anti roll bar oil pres oil temp gauge pod's,lockwood front rear grills,Tinted wind ws folding tow hook's,595s,connect2 ,at long last sohn and ap50 tank instaled ,revi ram air duct already fitted ! calipers painted,diff oil changed .
just oil lines to fit at some stage ( had them a while too)
180 of 400
just oil lines to fit at some stage ( had them a while too)
180 of 400
-
- Former Member
- Posts: 1216
- Joined: Fri Feb 12, 2016 6:18 pm
- RX-8: 231
- Location: Henley-on-Thames
- Has thanked: 18 times
- Been thanked: 78 times
Re: What have you done to your RX-8 today????
Even decent ones id stay clear of! It's not if its when will they go wrong, by go wrong I mean either won't come off or won't stay on!nightfire10 wrote: ↑Mon Dec 24, 2018 3:01 pmI think this has been talked about before ! Unless there decent ones I wouldn't be driving to fast with them or on track !
Sent from my SM-G930F using Tapatalk
2007 Galaxy grey 231.
RRP Parts: Full bridge, long tube header, cofs + tanks, pulleys, engine mounts, oil injectors, remap, race cat.
Other: Greddy sump, Autoexe exhaust, autoexe brake brace, ingalls engine brace, ultra racing f+r strut brace, hsd coilovers, whiteline Arbs, 4 pot brakes, r3 Diff, r3 interior and lots more
RRP Parts: Full bridge, long tube header, cofs + tanks, pulleys, engine mounts, oil injectors, remap, race cat.
Other: Greddy sump, Autoexe exhaust, autoexe brake brace, ingalls engine brace, ultra racing f+r strut brace, hsd coilovers, whiteline Arbs, 4 pot brakes, r3 Diff, r3 interior and lots more
-
- Forum Moderator
- Posts: 2496
- Joined: Wed May 17, 2017 12:27 pm
- RX-8: 231
- Colour: Sunlight Silver
- Location: Tyne & Wear
- Has thanked: 150 times
- Been thanked: 162 times
Re: What have you done to your RX-8 today????
Changed air filter.
How can something retained by two clips be such a PITA.
Brute force won out in the end
How can something retained by two clips be such a PITA.
Brute force won out in the end
- These users thanked the author bigpete8 for the post:
- johnbb99 (Mon Dec 24, 2018 4:30 pm)
Sunlight Silver 231
Pete/Peter him/he/hrh couldn't really care as have 3 siblings and was lucky not to get called by the dogs name.
Living with a rotary - 7 Years in
viewtopic.php?p=1105043#p1105043
Pete/Peter him/he/hrh couldn't really care as have 3 siblings and was lucky not to get called by the dogs name.
Living with a rotary - 7 Years in
viewtopic.php?p=1105043#p1105043
-
- Spin Doctor
- Posts: 32586
- Joined: Sat Sep 06, 2008 10:56 pm
- RX-8: 231
- Colour: Lightning Yellow
- Location: Groomsport, Co Down, NI
- Has thanked: 442 times
- Been thanked: 2088 times
Re: What have you done to your RX-8 today????
If those are alloy valve caps then expect them to be seized solid next time you try to check pressures, unless (and sometimes even if) you used some silicon grease when you fitted them.
The airbox is way easier to remove after the engine has been running, as the heat softens the concertina section. On 192s you can cut off the moulded clip that would hold the VFAD vacuum pipe on a 231. This makes the airbox even easier to remove/replace.
Sent from my SM-G800F using Tapatalk
The airbox is way easier to remove after the engine has been running, as the heat softens the concertina section. On 192s you can cut off the moulded clip that would hold the VFAD vacuum pipe on a 231. This makes the airbox even easier to remove/replace.
Sent from my SM-G800F using Tapatalk
-
- Club Member
- Posts: 2506
- Joined: Thu Mar 06, 2008 12:29 am
- RX-8: 231
- Colour: Sunlight Silver
- Location: Coventry
- Has thanked: 174 times
- Been thanked: 524 times
Re: What have you done to your RX-8 today????
Finally received my new oil reservoir from merlin motor sport, very nice bit of kit, just have to work out where I'm going to fit it.
Led side lights, purple Led interior & puddle lights, pz grills, Ryan rotary performance coils, sump, engine mounts & sohn, HME engine rebuild at 50k, RRP exhaust & high flow cat, racing beat revi intake including scoop, quick shifter, alloy filler cap, pz alloys, suspension, mazdaspeed spoiler, japspeed toe arms & hardrace camber arms, RRP custom remap
-
- Forum Moderator
- Posts: 2496
- Joined: Wed May 17, 2017 12:27 pm
- RX-8: 231
- Colour: Sunlight Silver
- Location: Tyne & Wear
- Has thanked: 150 times
- Been thanked: 162 times
Re: What have you done to your RX-8 today????
Damn had forgotten that about airbox...warpc0il wrote: ↑Mon Dec 24, 2018 6:05 pmIf those are alloy valve caps then expect them to be seized solid next time you try to check pressures, unless (and sometimes even if) you used some silicon grease when you fitted them.
The airbox is way easier to remove after the engine has been running, as the heat softens the concertina section. On 192s you can cut off the moulded clip that would hold the VFAD vacuum pipe on a 231. This makes the airbox even easier to remove/replace.
Sent from my SM-G800F using Tapatalk
Stone cold as stood since finished work on Thurs. ( intention had been to drive to pickup air filter but that didn't happen)
Sunlight Silver 231
Pete/Peter him/he/hrh couldn't really care as have 3 siblings and was lucky not to get called by the dogs name.
Living with a rotary - 7 Years in
viewtopic.php?p=1105043#p1105043
Pete/Peter him/he/hrh couldn't really care as have 3 siblings and was lucky not to get called by the dogs name.
Living with a rotary - 7 Years in
viewtopic.php?p=1105043#p1105043
-
- Club Member
- Posts: 2506
- Joined: Thu Mar 06, 2008 12:29 am
- RX-8: 231
- Colour: Sunlight Silver
- Location: Coventry
- Has thanked: 174 times
- Been thanked: 524 times
Re: What have you done to your RX-8 today????
Just ordered rex's Xmas present from ebc complete at of pads and discs, thanks to the club discount saved nearly £150 well worth being a paid up member
- These users thanked the author PaulAV for the post:
- 13Black (Tue Dec 25, 2018 8:03 pm)
Led side lights, purple Led interior & puddle lights, pz grills, Ryan rotary performance coils, sump, engine mounts & sohn, HME engine rebuild at 50k, RRP exhaust & high flow cat, racing beat revi intake including scoop, quick shifter, alloy filler cap, pz alloys, suspension, mazdaspeed spoiler, japspeed toe arms & hardrace camber arms, RRP custom remap
-
- Former Member
- Posts: 1968
- Joined: Thu Mar 01, 2018 12:47 pm
- Location: south east London
- Has thanked: 38 times
- Been thanked: 116 times
Re: What have you done to your RX-8 today????
Start to pull the rust bucket apart
You do not have the required permissions to view the files attached to this post.
- These users thanked the author mi60o0 for the post:
- ChrisHolmes (Thu Dec 27, 2018 11:48 am)
LEXUS LS430 4.3 v8 family car
Done exhaust and work wheels
Mx5 nd soul red Mike daily and work horse
Jessy’s Jaguar xkr 4.2 supercharged for fun family days
Done exhaust and work wheels
Mx5 nd soul red Mike daily and work horse
Jessy’s Jaguar xkr 4.2 supercharged for fun family days
-
- Former Member
- Posts: 1390
- Joined: Sat May 19, 2018 4:55 pm
- Has thanked: 49 times
- Been thanked: 20 times
Re: What have you done to your RX-8 today????
It still looks like the engine is missing every time you pop the bonnet!
-
- Club Member
- Posts: 507
- Joined: Fri Mar 23, 2018 3:05 pm
- RX-8: Kuro
- Colour: Sparkling Black
- Location: Hurst Green, East Sussex
- Has thanked: 86 times
- Been thanked: 38 times
Re: What have you done to your RX-8 today????
Single resonated RRP DeCat and Pettit/Miltek CatBack fitted... Sounds great. First test wiring up custom matrix lights on the bench too. AEM CAI first on the list tomorrow, then slicing open rear lights to start advancing the custom lights. Maybe spraying the PZ mirrors too, depending on how I get on.
Kuro 174/500.
RRP midpipe (single resonator) w/ Pettit/Milltek cat-back, RRP MK2 Coils and MSD leads, AEM Cold Air Intake, RRP Custom Map, Royal Steering Wheels custom wheel. Mazdaspeed bodykit, Team Dynamics Pro Race 1.2s, Smoked LED rear lights, Stoney Racing Hose Kit, Lots of red in the engine bay.
#174’s journey: viewtopic.php?f=104&t=78506
RRP midpipe (single resonator) w/ Pettit/Milltek cat-back, RRP MK2 Coils and MSD leads, AEM Cold Air Intake, RRP Custom Map, Royal Steering Wheels custom wheel. Mazdaspeed bodykit, Team Dynamics Pro Race 1.2s, Smoked LED rear lights, Stoney Racing Hose Kit, Lots of red in the engine bay.
#174’s journey: viewtopic.php?f=104&t=78506
-
- Former Member
- Posts: 1968
- Joined: Thu Mar 01, 2018 12:47 pm
- Location: south east London
- Has thanked: 38 times
- Been thanked: 116 times
Re: What have you done to your RX-8 today????
Tomorrow new crank sensor new gear box oil and few JDM interior bits
LEXUS LS430 4.3 v8 family car
Done exhaust and work wheels
Mx5 nd soul red Mike daily and work horse
Jessy’s Jaguar xkr 4.2 supercharged for fun family days
Done exhaust and work wheels
Mx5 nd soul red Mike daily and work horse
Jessy’s Jaguar xkr 4.2 supercharged for fun family days
-
- Club Member
- Posts: 507
- Joined: Fri Mar 23, 2018 3:05 pm
- RX-8: Kuro
- Colour: Sparkling Black
- Location: Hurst Green, East Sussex
- Has thanked: 86 times
- Been thanked: 38 times
Re: What have you done to your RX-8 today????
Oh, yeah, also tomorrow engine and gearbox oil change
Kuro 174/500.
RRP midpipe (single resonator) w/ Pettit/Milltek cat-back, RRP MK2 Coils and MSD leads, AEM Cold Air Intake, RRP Custom Map, Royal Steering Wheels custom wheel. Mazdaspeed bodykit, Team Dynamics Pro Race 1.2s, Smoked LED rear lights, Stoney Racing Hose Kit, Lots of red in the engine bay.
#174’s journey: viewtopic.php?f=104&t=78506
RRP midpipe (single resonator) w/ Pettit/Milltek cat-back, RRP MK2 Coils and MSD leads, AEM Cold Air Intake, RRP Custom Map, Royal Steering Wheels custom wheel. Mazdaspeed bodykit, Team Dynamics Pro Race 1.2s, Smoked LED rear lights, Stoney Racing Hose Kit, Lots of red in the engine bay.
#174’s journey: viewtopic.php?f=104&t=78506