Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Details of any aftermarket goods for the RX8.
Remember that this may invalidate the warranty. - The club takes no responsibility at all for any aftermarket additions to the car.
Post Reply
User avatar
LeeW
Club Member
Club Member
Posts: 229
Joined: Fri Mar 23, 2018 3:05 pm
RX-8: Kuro
Colour: Sparkling Black
Location: Hurst Green, East Sussex
Has thanked: 51 times
Been thanked: 32 times

Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by LeeW » Fri Mar 20, 2020 5:34 pm

Can anyone recommend what mesh to use on the Mazdaspeed front end? The only thing i know is i want it black, not silver.

Not sure what size pitch is recommended for adequate protection to the oil coolers and radiator? Is there any reason to go for ABS plastic rather than stainless steel?

Any recommendations are welcome, my bodywork is now moving forward so want to buy something soon.

Cheers in advance
07' Kuro
RRP Single Res midpipe w/ Pettit/Milltek cat-back, RRP MK2 Coils and leads, AEM CAI, RRP Custom Map, RSW Custom Steering Wheel.

RX8 Story (slow progress): viewtopic.php?f=104&t=78506

User avatar
warpc0il
Spin Doctor
Spin Doctor
Posts: 26892
Joined: Sat Sep 06, 2008 10:56 pm
RX-8: 231
Colour: Lightning Yellow
Location: Groomsport, Co Down, NI
Has thanked: 505 times
Been thanked: 2071 times
Contact:

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by warpc0il » Fri Mar 20, 2020 5:42 pm

I use this stuff as it's tough, UV stable, cheap and easy to replace if required.

Image

Amazon link was the first one to come up but it's available in all sorts of places, including Poundland
Dave
The Spin Doctor ™
uǝǝɹɔs ɹnoʎ ʇɹǝʌuı ǝsɐǝld :ɹoɹɹǝ

User avatar
LeeW
Club Member
Club Member
Posts: 229
Joined: Fri Mar 23, 2018 3:05 pm
RX-8: Kuro
Colour: Sparkling Black
Location: Hurst Green, East Sussex
Has thanked: 51 times
Been thanked: 32 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by LeeW » Fri Mar 20, 2020 6:06 pm

baring in mind its for gutters, does that stuff only come in 16x5 strips? i would want something to cover the whole middle opening in one piece. having to join loads together will look a bit naff?
07' Kuro
RRP Single Res midpipe w/ Pettit/Milltek cat-back, RRP MK2 Coils and leads, AEM CAI, RRP Custom Map, RSW Custom Steering Wheel.

RX8 Story (slow progress): viewtopic.php?f=104&t=78506

User avatar
warpc0il
Spin Doctor
Spin Doctor
Posts: 26892
Joined: Sat Sep 06, 2008 10:56 pm
RX-8: 231
Colour: Lightning Yellow
Location: Groomsport, Co Down, NI
Has thanked: 505 times
Been thanked: 2071 times
Contact:

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by warpc0il » Fri Mar 20, 2020 6:09 pm

How deep is the opening?
Spoiler:
@Nigel - You're barred from responding to this question [-X
These users thanked the author warpc0il for the post:
Vj4sothername (Fri Mar 20, 2020 7:21 pm)
Dave
The Spin Doctor ™
uǝǝɹɔs ɹnoʎ ʇɹǝʌuı ǝsɐǝld :ɹoɹɹǝ

User avatar
LeeW
Club Member
Club Member
Posts: 229
Joined: Fri Mar 23, 2018 3:05 pm
RX-8: Kuro
Colour: Sparkling Black
Location: Hurst Green, East Sussex
Has thanked: 51 times
Been thanked: 32 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by LeeW » Fri Mar 20, 2020 6:13 pm

hahaha.

haven't actually measured but it's more than 16x5. 60x30 if i had to guess.
07' Kuro
RRP Single Res midpipe w/ Pettit/Milltek cat-back, RRP MK2 Coils and leads, AEM CAI, RRP Custom Map, RSW Custom Steering Wheel.

RX8 Story (slow progress): viewtopic.php?f=104&t=78506

User avatar
LeeW
Club Member
Club Member
Posts: 229
Joined: Fri Mar 23, 2018 3:05 pm
RX-8: Kuro
Colour: Sparkling Black
Location: Hurst Green, East Sussex
Has thanked: 51 times
Been thanked: 32 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by LeeW » Wed Nov 25, 2020 10:31 am

What's the deal with the contrasting grey lower sections of the MS kit? Is it always that colour because thats the look of the genuine? Is it widely accepted that it would look bad if all matching body coloured, even on a black RX8? And what is the 'official' colour of those sections that I should tell my body guy?
07' Kuro
RRP Single Res midpipe w/ Pettit/Milltek cat-back, RRP MK2 Coils and leads, AEM CAI, RRP Custom Map, RSW Custom Steering Wheel.

RX8 Story (slow progress): viewtopic.php?f=104&t=78506

User avatar
Ryan Rotary Performance
Sponsor Trader
Sponsor Trader
Posts: 1610
Joined: Fri Jan 27, 2017 8:06 pm
RX-8: Supercharged
Colour: Brilliant Black
Location: Rugby and Stonham Aspal
Has thanked: 204 times
Been thanked: 712 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by Ryan Rotary Performance » Wed Nov 25, 2020 12:08 pm

warpc0il wrote:
Fri Mar 20, 2020 5:42 pm
I use this stuff as it's tough, UV stable, cheap and easy to replace if required.

Image

Amazon link was the first one to come up but it's available in all sorts of places, including Poundland
Cheap and Nasty IMO (you got the poundland Decals to go with them? :lol: ), if you just look on Ebay and search universal car mesh or grill a plethora of returns will show all with different styles to match the look you want.

Merlin motorsports is another shout.

untakenname
Club Member
Club Member
Posts: 889
Joined: Wed Jul 02, 2014 10:18 am
RX-8: 231
Colour: Kuro Black
Location: London
Has thanked: 101 times
Been thanked: 127 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by untakenname » Wed Nov 25, 2020 12:32 pm

I originally tried gutter guard but it melted so then used some aluminium mesh that is designed for car grills on my rear bumper, it holds its shape and is easy to mould, has lasted 3 years now with no corrosion.
IMG_20180507_170145.jpg

User avatar
LeeW
Club Member
Club Member
Posts: 229
Joined: Fri Mar 23, 2018 3:05 pm
RX-8: Kuro
Colour: Sparkling Black
Location: Hurst Green, East Sussex
Has thanked: 51 times
Been thanked: 32 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by LeeW » Wed Nov 25, 2020 1:59 pm

Thanks for the replies guys. I sort of got off topic on my own old thread though, rather than start a new thread. My last post was asking about the paint colour differences on the MS kit, not mesh anymore....
07' Kuro
RRP Single Res midpipe w/ Pettit/Milltek cat-back, RRP MK2 Coils and leads, AEM CAI, RRP Custom Map, RSW Custom Steering Wheel.

RX8 Story (slow progress): viewtopic.php?f=104&t=78506

User avatar
pfletcher83
Club Member
Club Member
Posts: 752
Joined: Sun Sep 21, 2008 7:21 pm
RX-8: 231
Colour: Winning Blue
Location: Bolton
Has thanked: 8 times
Been thanked: 20 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by pfletcher83 » Wed Nov 25, 2020 5:36 pm

AFAIK there is no official code for the grey - at least none that i could find and that included phoning mazda themselves.

The colour i had mine painted was - a39 (Mitsubishi graphite gray) which seems spot-on.

Not the best pics but gives you an idea
DSC07557.JPG
DSC07557.JPG (123.33 KiB) Viewed 323 times
DSC07649.JPG
DSC07649.JPG (158.33 KiB) Viewed 323 times
DSC07666.JPG
DSC07666.JPG (95.97 KiB) Viewed 323 times
Paul
These users thanked the author pfletcher83 for the post:
untakenname (Fri Nov 27, 2020 8:42 pm)

User avatar
LeeW
Club Member
Club Member
Posts: 229
Joined: Fri Mar 23, 2018 3:05 pm
RX-8: Kuro
Colour: Sparkling Black
Location: Hurst Green, East Sussex
Has thanked: 51 times
Been thanked: 32 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by LeeW » Thu Nov 26, 2020 8:33 pm

Cheers Paul

They’re beautiful pictures. Is that a genuine rear or replica?
07' Kuro
RRP Single Res midpipe w/ Pettit/Milltek cat-back, RRP MK2 Coils and leads, AEM CAI, RRP Custom Map, RSW Custom Steering Wheel.

RX8 Story (slow progress): viewtopic.php?f=104&t=78506

User avatar
pfletcher83
Club Member
Club Member
Posts: 752
Joined: Sun Sep 21, 2008 7:21 pm
RX-8: 231
Colour: Winning Blue
Location: Bolton
Has thanked: 8 times
Been thanked: 20 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by pfletcher83 » Fri Nov 27, 2020 12:48 pm

Replica unfortunately, tried to get an original at the time but they were pretty much impossible to come by.
Its been on 10 years and still looks in perfect condition so i cant complain really :thumleft:

Been trying to get hold for some genuine R-Magic side skirts for years but they are even more difficult to come by without importing from japan and taking out a 2nd mortgage :x

Thanks

Paul

User avatar
LeeW
Club Member
Club Member
Posts: 229
Joined: Fri Mar 23, 2018 3:05 pm
RX-8: Kuro
Colour: Sparkling Black
Location: Hurst Green, East Sussex
Has thanked: 51 times
Been thanked: 32 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by LeeW » Wed Jan 27, 2021 9:11 am

pfletcher83 wrote:
Fri Nov 27, 2020 12:48 pm
Replica unfortunately, tried to get an original at the time but they were pretty much impossible to come by.
Its been on 10 years and still looks in perfect condition so i cant complain really :thumleft:

Been trying to get hold for some genuine R-Magic side skirts for years but they are even more difficult to come by without importing from japan and taking out a 2nd mortgage :x

Thanks

Paul
Looks great. Would you happen to have any pictures of how you braced the bottom on the tabs? I see the genuine came with Z shaped brackets but obviously nothing with the reps. Did you source some similar brackets?

Also, have you left it with no fog light? Or does anyone have any recommendations for a replacement foglight that can be fit nicely into the bumper?
07' Kuro
RRP Single Res midpipe w/ Pettit/Milltek cat-back, RRP MK2 Coils and leads, AEM CAI, RRP Custom Map, RSW Custom Steering Wheel.

RX8 Story (slow progress): viewtopic.php?f=104&t=78506

User avatar
pfletcher83
Club Member
Club Member
Posts: 752
Joined: Sun Sep 21, 2008 7:21 pm
RX-8: 231
Colour: Winning Blue
Location: Bolton
Has thanked: 8 times
Been thanked: 20 times

Re: Mazdaspeed Bumper (Aerokit Replica) Mesh recommendations

Post by pfletcher83 » Fri Jan 29, 2021 9:14 am

I didnt fit the bumper but i have been under and can say that the bottom tabs are not secured to anything. Its secured to the bumper and in the wheel arches
I noticed it when i went to wire in a fog light for MOT. It did concern me at the time that windflow could cause it to bow, but ive had someone follow me at motorway :whistle: speeds and there is no movement, still solid to this day.

I dont have permanent fog light, i just bolt on a cheap one for MOT, or when its foggy :D

Paul
These users thanked the author pfletcher83 for the post:
LeeW (Fri Jan 29, 2021 1:03 pm)

Post Reply

Return to “Aftermarket”