Hi all,
I somehow seem to have lost both sides while doing the usual tinkering,,
Anyone got a set they are happy to package up for me?
Thanks
Kevin

Sent from my FIG-LX1 using Tapatalk

Looking for the sensor on the Abs block. Bigpetes going to have a look for one for me tomorrow. But in the event he doesn't find one does anyone have one kicking about?

Hi all, not sure if this is in the right section but I’m sure someone will be kind enough to point that out if it isn’t.

Anyway, I went to my first trackday yesterday and I really enjoyed it. My car is a pz but the front drivers side strut and spring is off a standard rx8 and the rear shock is...

Looking to buy a right hand exhaust surround, think they all come in black. F151-50-361

Looking for a decent set of used ignition coils, leads and hopefully spark plugs but the spark plugs don't matter as much as the other two.

Giys,

After the center console left and rights as below if anyone has them? Must be good condition

Screenshot_20201121-113256_eBay.jpg

Looking for a genuine rx8 branded drivers mat in good condition.

Mine has worn through at the heel but all the others are still like new so dont want to stump up for a full set if i can help it.

Paul

Looking to buy both L& R front suspension upper arms as the bolts are looking a little ropey and the torque rotation is very suspect. Seeing a lot of replacement parts on Fleabay but wondering if any are worth a punt or just stick to OEM and go for the extra cost at a guaranteed fix?

F151-34-200B...

Hello again,

Does anyone have a driver side metal exhaust shroud finisher knocking around?

I believe they were standard on the Evolve models. Had a gander and can't seem to find any for sale apart from the alleged one I already bought which turned out to be for the passenger side... #-o

Ta,...

Must be low mileage, low keepers and in as good as condition to my much cherished series 1.
Top price paid for the right car.
Let me know if you're interested in selling yours or if you know someone who is.

Thanks in advance.

Hi

I've got hold of a sat nav unit and tablet so looking to do the whole carputer thingy, however the sat nav I got did not come with the centre dash surround with the cut out for the sat nav unit.

Does anyone have one going spare? Again this is just the plastic surround which goes around the...

Anyone got any RB anti roll bars for sale (front and rear)? If not I may have to buy some new car parts for a change :lol:

I recently purchased a reconditioned rack for my S1. However I need to replacement the Universal Joint/knuckle before it can be fitted. I contacted the company who I purchased the rack from, the complete ground in Yorkshire, but they said they can’t help me.

I also tired big Pete but he has none...

Anyone got a good one kicking about? The one in the cat I've taken off the car refuses to budge and has very kindly rounded down..

IMG-20201114-WA0000.jpeg

Guess I'm just going to fit the cat without a sensor until I get a replacement. Not that it's being driven anywhere until the MOT.

Hi all, I am looking for a decent set of coils, ideally OEM Rev C, in good working order

Don’t mind D585 but they tend to sell for more than I would want to spend (sub £100 really)

Thanks

Nick

Trying to find somewhere in UK that is selling the rear link arm dust boots.

2 x F151-28-4A3
2 x F151-28-4B3
4 x F151-28-503

Any help really appreciated as all I can find are US sites

Hi!

I'm looking for a set of R3 stock suspension with top mounts included if possible. My R3 I purchased a few weeks back now came with a HSD coilover set installed and i believe top mounts may have been swapped out? (might be wrong but I dont know much about it), and while I want to keep them on...

Anyone selling a pair of S1 rear uprights / hubs ? Not too fused about condition, plan is to fit new bearings and longer wheel studs and not have to take mine off the road.

Thanks

Sent from my J8210 using Tapatalk

Just posting on the off chance that someone on here works in an engineering shop where they could knock up a couple of strips of steel to the dimensions above to assist me in measuring apex seal groove dimensions.

W 0.075 (1.905mm x H 0.5 (12.7mm) x L 4 (101.6mm) and 0.078 (1.9812mm) x .5 (12.7mm)...