Rmagic Spoiler Install on S1
-
Rotarty8
- Forum Guest

- Posts: 3
- Joined: Sat Aug 29, 2026 8:10 pm
- RX-8: 231
- Colour: Aluminium Silver
- Has thanked: 2 times
- Been thanked: 0
Rmagic Spoiler Install on S1
Hi there, this is my 1st post on here and I've recently bought an Rmagic spoiler for my 2003 S1. Just looking some advice on how to install it? Thanks
- HarSc
- Club Member

- Posts: 6301
- Joined: Wed Aug 12, 2020 1:29 am
- RX-8: R3
- Colour: Crystal White
- Location: Doncaster
- Has thanked: 1152 times
- Been thanked: 1141 times
Re: Rmagic Spoiler Install on S1
Bolts.... Hopefully
Depends entirely on how it's intended to marry up.
With it being aftermarket, I wouldn't expect it to bolt to any existing holes (unless your bootlid already has a Mazdaspeed/hoop/R3 spoiler, as they all use the same outboard bolt points).
Does it have any rivnuts in the spoiler itself? Holes? Studs? You'll be best off using masking tape and transferring it, or using a paint pen to witness mark the mounting positions before drilling anything for definite.
Photos of both the boot and spoiler will help in this regard as it's not a common spoiler that many will have seen/installed.
- warpc0il
- Spin Doctor

- Posts: 34196
- Joined: Sat Sep 06, 2008 10:56 pm
- RX-8: 231
- Colour: Lightning Yellow
- Location: Groomsport, Co Down, NI
- Has thanked: 960 times
- Been thanked: 3894 times
- Contact:
Re: Rmagic Spoiler Install on S1
This may be of some help viewtopic.php?t=37203&hilit=spoiler
as may this viewtopic.php?t=24152&hilit=spoiler
as may this viewtopic.php?t=24152&hilit=spoiler
-
Rotarty8
- Forum Guest

- Posts: 3
- Joined: Sat Aug 29, 2026 8:10 pm
- RX-8: 231
- Colour: Aluminium Silver
- Has thanked: 2 times
- Been thanked: 0
Re: Rmagic Spoiler Install on S1
HarSc wrote: ↑Sun Aug 30, 2026 12:07 pm
Bolts.... Hopefully![]()
Depends entirely on how it's intended to marry up.
With it being aftermarket, I wouldn't expect it to bolt to any existing holes (unless your bootlid already has a Mazdaspeed/hoop/R3 spoiler, as they all use the same outboard bolt points).
Does it have any rivnuts in the spoiler itself? Holes? Studs? You'll be best off using masking tape and transferring it, or using a paint pen to witness mark the mounting positions before drilling anything for definite.
Photos of both the boot and spoiler will help in this regard as it's not a common spoiler that many will have seen/installed.
Thanks for the reply! Yes, I assumed I'd have to remove the boot spoiler anyway but this is the way it'll hopefully look after fitted (link below).
https://share.google/jcG6EkHrYfUgjAwnz
-
Rotarty8
- Forum Guest

- Posts: 3
- Joined: Sat Aug 29, 2026 8:10 pm
- RX-8: 231
- Colour: Aluminium Silver
- Has thanked: 2 times
- Been thanked: 0
Re: Rmagic Spoiler Install on S1
warpc0il wrote: ↑Sun Aug 30, 2026 12:40 pmThis may be of some help viewtopic.php?t=37203&hilit=spoiler
as may this viewtopic.php?t=24152&hilit=spoiler
Thanks for that, hoping this will be easy enough to install.
https://share.google/jcG6EkHrYfUgjAwnz
-
DominoRotary
- Forum Guest

- Posts: 1
- Joined: Sun Sep 06, 2026 3:27 am
- RX-8: 231
- Colour: Winning Blue
- Has thanked: 0
- Been thanked: 0
Re: Rmagic Spoiler Install on S1
Please update when you get it fitted! I plan on ordering the same in a week or two to fit onto mine so that's good timing!
On another note, where did you order yours from? I've seen 2 ebay listing's from the same place at different prices and was going to grab the cheaper one to save some money
On another note, where did you order yours from? I've seen 2 ebay listing's from the same place at different prices and was going to grab the cheaper one to save some money


